1

Тема: Китайский VT310 (внутри TK118)

Купил такой девайс VT310

http://s2.ipicture.ru/uploads/20120111/thumbs/DaOW7kRw.jpg

внутри оказался tk118 (мелкими буквами написано)

и не как не дам ему ладу, на СМС не отвечает.. что только не делал...один раз чудным образом ответил - прислал координаты.

Весь инет уже переискал, а информации не много.. Не кто не сталкивался с таким чудом? К нему на диске идёт мануал..
Например простейший код 8880000 (где 0000 пароль) - должен в ответ прислать свое местоположение...а в ответ тишина..
Присылает свое местоположение только после звонка.. smile

Внутри он выглядит так:

http://s2.ipicture.ru/uploads/20120111/K36xaHQx.jpg
http://s2.ipicture.ru/uploads/20120111/sjVU53we.jpg

2

Re: Китайский VT310 (внутри TK118)

sad неужели нету идей?

3

Re: Китайский VT310 (внутри TK118)

Для начала список команд дайте которыми вы его конфигурируете и соответственно что он вам отвечает.

4

Re: Китайский VT310 (внутри TK118)

Вот выдержка с командами настройки из мануала:
Не на одну из команд трекер не отвечает sad

3.1 SMS location inquiry
Format: 888+0000 (default password is 0000)
For example you send 8880000 to the tracker, you will get a reply SMS with link.
http//map.google.com/?q=22.677327N,114.120738E
SPEED:0.22240KM/H
Time:10:47:18 Date:03/05/11
IMEI:353509000924608
Visit the link by your phone or computer; you will know the name of the location in detail.
3.2 Set Center Number
Set the center number by SMS through mobile phone. If the setup is successful, the sender will receive “CONFIG OK” response message from the tracker
Format: #710# center number # user password ##
For example: #710#134xxxxxxxx#0000##
Note: All alarming information thereafter including SOS, low power, electronic fence etc. will be sent to this number. 0000 is the default password.
3.3 Set pre-stored numbers
Before setting center number, the device will respond to command from any mobile phone NO. After setting successfully; the device will not respond to other numbers except the pre-set number. 9 numbers can be pre-set at most.
Format:#711#phone number # password d# serial##
For example:You want to set three stored numbers
#711# Phone number 1#0000#1## ---------------The first number
#711#phone number 2#0000#2## ----------------The second number
#711#phone number 3#0000#3## ----------------The third number
Only one phone number can be set per time, as above mentioned three numbers need to send SMS three times separately. The new numbers will replace the old numbers, and it will send confirmation to the sender if the password is right….CONFG OK
3.4 SOS button(Emergency call button)
In case of emergency, please press SOS button over 3 seconds, an emergency will be reported to center number with current location, and call the pre-set numbers in turn.
3.5 Cut power supply by SMS
Format: 232+password
Example: 2320000
After sending command successfully, the tracker will return a message “SET OK” and cut power supply of the vehicle.
3.6 Cut oil supply by SMS
Format: 233+password
Example: 2330000
After sending command successfully, the tracker will return a message “SET OK” and cut oil supply of the vehicle.
3.7 Resume power supply and oil supply by SMS
Format: 230+password
Example: 2300000
After sending command successfully, the tracker will return a message “SET OK” and resume power supply and oil supply of the vehicle.
3.8 Change the password
Format: #770# new password # old password ##”
Example: #770#1111#0000##
After sending command successfully, the tracker will return a message “CHANGE OK”. And the user password will be changed to: 1111.
Remind: Now all set-up format’s password change to “1111”
3.9 E-fence set up
Set up an e-fence for the tracker to restrict its movements within an area. The tracker will send the message to the authorized numbers when it goes beyond the district. If the setting is correct, the tracker will reply CONFIG OK to the sender, and if the password is wrong, it will reply PASSWORD ER.
Tips: Only pre-set number is set successfully, this function can work
Format: #750#radius (5 digits)#sampling interval (minutes)#password # #
For example: #750#500#5#0000##
A round fence with the radius of 500 meters, the current location as center is set. When the tracker goes out this area, the tracker will send alarm information “OBJECT OUT” to the center number.
3.10 Cancel E-fence
Format: #760#password##
Example: #760#0000##
After the tracker receiving this command, all fence settings will be cancelled, and return a SMS “CONFIG OK”. The device will reply “PASSORD ER” if the format’s password is wrong.
3.11 Set Server connection
Format: #803# Fixed IP address# port number#4-digit password##
This command is used to set GPRS center server address, which could be fixed IP number. After the setup is successful, the module will send a reply with ‘&803&successful setting&&’ or ‘&803&PASSWORD ER&&’ if the password is wrong.
Example: #803# 116.255.141.169#8169#0000##
Setup via domain name:
Example: #803#www.gps06.com#8169#0000##
3.12 Set APN
Format: #802#APN letters or digits, 4-20 bits # Log user name letters or digits 4-20 bits in # Log password letter or digits 4-20 bits in # terminal password 4 bits ##
The default APN is CMNET, if the APN doesn’t have login user name and password, it can be set 0.
Example 1: #802#0#0#0#0000## 
APN is CMNET, no login user name, no login password
Example 2: #802#CCDLEN#QIUXIA.21#RX0000#0000##
APN is CCDLEN; the login user name is QIUXIA.21 and login password is RX0000.
Note: The default APN of this product is CMNET.
3.13 Regular Upload Interval Setup
The defaulted factory upload interval of this device is 2 minutes for getting the point and 10 minutes for uploading one piece of location information. The user may change such parameter according to actual demand.
Format: #730# Sampling interval # Pieces of uploads # User password ##
For example: #730#20#4#0000##
Note: The parameter “20” indicates getting one point every 20s; after getting points accumulatively for 4 times, upload one piece of location information with the upload interval as 20*4=80s.
3.14 Auxiliary Functions
(1)#901## Command of reading user parameters;
(2)#902## Command of reading GPRS parameters
(3)#903## Restart command
(4)#904## GPRS connection command
(5)#905## GPRS disconnection command

5

Re: Китайский VT310 (внутри TK118)

При звонке на него присылает нечто типа:

http://www.gps06.com/?lat=бла.бла.бла...
SPEED:0.22240KM/H
Time:10:47:18 Date:03/05/11
IMEI:353509000924608

Отредактировано wizardlg (13-01-2012 09:28:29)

6

Re: Китайский VT310 (внутри TK118)

И симки разные тыкал... а толку ноль sad

7

Re: Китайский VT310 (внутри TK118)

У Вас модель которая работает только через СМС и звонки.
Такое было с Xexun (поддельным) в свое время.

8

Re: Китайский VT310 (внутри TK118)

wizardlg пишет:

И симки разные тыкал... а толку ноль sad

У меня брат близнец Вашего зверька ( судя по фотографиям).
отзывается на смс следующих команд -
(скопировал из мануала)

Добавление пользователей:


#711#phone number # password d# serial##

For example:You want to set three stored numbers 

#711# Phone number 1#0000#1## ---------------The first number
#711#phone number 2#0000#2## ----------------The second number
  #711#phone number 3#0000#3## ----------------The third number


3.5 Cut power supply by SMS

Format: 232+password

Example: 2320000

After sending command successfully, the tracker will return a message “SET OK” and cut power supply of the vehicle.

3.6 Cut oil supply by SMS

Format: 233+password

Example: 2330000

After sending command successfully, the tracker will return a message “SET OK” and cut oil supply of the vehicle.

3.7 Resume power supply and oil supply by SMS

Format: 230+password

Example: 2300000

After sending command successfully, the tracker will return a message “SET OK” and resume power supply and oil supply of the vehicle.

3.8 Change the password

Format: #770# new password # old password ##”

Example: #770#1111#0000##

After sending command successfully, the tracker will return a message “CHANGE OK”. And the user password will be changed to: 1111.

Remind: Now all set-up format’s password change to “1111” 

3.9 E-fence set up

Set up an e-fence for the tracker to restrict its movements within an area. The tracker will send the message to the authorized numbers when it goes beyond the district. If the setting is correct, the tracker will reply CONFIG OK to the sender, and if the password is wrong, it will reply PASSWORD ER.

Tips: Only pre-set number is set successfully, this function can work 

Format: #750#radius (5 digits)#sampling interval (minutes)#password # #

For example: #750#500#5#0000##

A round fence with the radius of 500 meters, the current location as center is set. When the tracker goes out this area, the tracker will send alarm information “OBJECT OUT” to the center number.

3.10 Cancel E-fence

Format: #760#password##

Example: #760#0000##

After the tracker receiving this command, all fence settings will be cancelled, and return a SMS “CONFIG OK”. The device will reply “PASSORD ER” if the format’s password is wrong.

3.11 Set Server connection 

Format: #803# Fixed IP address# port number#4-digit password##

This command is used to set GPRS center server address, which could be fixed IP number. After the setup is successful, the module will send a reply with ‘&803&successful setting&&’ or ‘&803&PASSWORD ER&&’ if the password is wrong.

Example: #803# 116.255.141.169#8169#0000##

Setup via domain name: Example: #803#www.gps06.com#8169#0000##

3.12 Set APN 

Format: #802#APN letters or digits, 4-20 bits # Log user name letters or digits 4-20 bits in # Log password letter or digits 4-20 bits in # terminal password 4 bits ##

The default APN is CMNET, if the APN doesn’t have login user name and password, it can be set 0. 

Example 1: #802#0#0#0#0000##   APN is CMNET, no login user name, no login password

#802#internet.mts.ru#mts#mts#7799##

Example 2: #802#CCDLEN#QIUXIA.21#RX0000#0000## APN is CCDLEN; the login user name is QIUXIA.21 and login password is RX0000.  Note: The default APN of this product is CMNET.

3.13 Regular Upload Interval Setup

The defaulted factory upload interval of this device is 2 minutes for getting the point and 10 minutes for uploading one piece of location information. The user may change such parameter according to actual demand.

Format: #730# Sampling interval # Pieces of uploads # User password ##

For example: #730#20#4#0000##

Note: The parameter “20” indicates getting one point every 20s; after getting points accumulatively for 4 times, upload one piece of location information with the upload interval as 20*4=80s. 

3.14 Auxiliary Functions

(1)#901## Command of reading user parameters;

(2)#902## Command of reading GPRS parameters

(3)#903## Restart command

(4)#904## GPRS connection command

(5)#905## GPRS disconnection command

9

Re: Китайский VT310 (внутри TK118)

smile Молчит как партизан.... осталось только паяльником в "Ж" и пытать sad

10

Re: Китайский VT310 (внутри TK118)

Да уж, либо в качестве витринного экспоната в магазин знакомым:)
"А он мигает"?

11

Re: Китайский VT310 (внутри TK118)

smile) Мигает...на него можно звонить....он смс в ответ даже шлёт....